The amount of oil you’ll need depends on the size of your pot and the size of your turkey. … You’ll need enough oil to cover your entire turkey, but not so much that it spills over. A general guideline is to use 3 gallons of oil for a 30 qt. pot and 3 1/3 gallons of oil for a 32 qt.
How many gallons of oil does it take to fry a turkey?
Place the pot on the burner and clip the deep-fry thermometer to the side of the pot. Fill the pot with peanut or canola oil up to the mark you made earlier—you’ll need 4 to 5 gallons to fry a 12- to 14-pound turkey in a 30-quart pot.
Is 3 gallons of peanut oil enough?
You don’t need much oil, as 3 to 4 gallons will be enough. You won’t need too much time either, as it should only take about 32 minutes or so.
How long does it take to heat 3 gallons of oil in a turkey fryer?
Approximately 30 minutes. Be sure the lid is on the fryer to help speed up the process. Use good quality oil with a smoke point of 400°f or higher. Vegetable, corn, canola, soybean, or peanut oils are safe to use.
How many turkeys can I fry with 3 gallons of peanut oil?
Peanut oil can usually be used three or four times to fry turkeys before it shows signs of going bad, according to the Texas Peanut Producers Board via The National Turkey Federation. Watch for foaming, darkening or smoking excessively — these are all signs that your oil has gone rancid and needs to be discarded.
Should turkey be room temperature before frying?
Remove the turkey from the brine, rinse and pat dry. Allow to sit at room temperature for at least 30 minutes prior to cooking. … The bird will reach an internal temperature of 161 degrees F due to carry over cooking. Carve as desired.
Does turkey have to be fully submerged in oil?
When working with large amounts of hot oil, select a cooking vessel large enough to completely submerge the turkey without it spilling over. The oil should cover the turkey by 1 to 2 inches. Select a safe location outdoors for deep fat frying a turkey. Heat the cooking oil to 350°F.
How long does it take to heat up 5 gallons of peanut oil?
Heating the oil: In our fryer, ~5 gallons of oil took ~40 minutes to heat up to 175 degrees. You have to watch this process the entire time. If the oil overheats – it can ignite. Of course, you should always keep the lid off during heating, to avoid flash fires.
How long does oil take to get to 350?
What setting on the stove is 350 oil? Set your burner on medium and let your pan of oil heat for around 5 to 10 minutes. Put the meat thermometer in the center of the oil to check the temperature. The oil should be between 350 degrees Fahrenheit (177 Celsius) and 400 F (205 C), depending on what you’re cooking.
What type of oil is best for frying?
What’s the Best Oil for Frying?
- Vegetable Oil: Best All-Purpose Oil for Frying. Andres Ruffo / EyeEmGetty Images. …
- Peanut Oil: Best Oil for Deep-Frying. …
- Corn Oil: Best All-Purpose Oil for Frying. …
- Olive Oil: Best Oil for Pan-Frying. …
- Canola Oil: Best All-Purpose Oil for Frying. …
- Coconut Oil: Best Oil for Sautéing.
How long does it take to fry a turkey in peanut oil?
Heat peanut oil in a turkey fryer or a very, very large stockpot to 350 °F. Lower turkey into hot oil, very carefully, making sure it is fully submerged. Fry turkey for 3 minutes per pound plus 5 minutes per bird.
Can you keep oil after frying?
Yes, it is OK to reuse fry oil. Here’s how to clean and store it: ① Once you’ve finished frying, let the oil cool. … ② Place a fine-mesh strainer or cheesecloth (even better if you use both) over the container you plan to store it in and strain the oil.
How many turkeys can you fry in peanut oil?
Peanut oil can usually be used three or four times to fry turkeys before it shows signs of going bad, according to the Texas Peanut Producers Board via The National Turkey Federation.